Engine build thread!

N/A build discussion
 Reply
User avatar

By ChicagoMike
- Wed Oct 03, 2007 2:04 am #25084
Greasedmonkey wrote: but I will be getting a Hytech.


Great headeR!! :thumb:
User avatar

By Greasedmonkey
- Wed Oct 03, 2007 2:58 am #25088 The only thing is I need to decide what size exhaust to get. Im shooting for 200hp. and I will get the Kteller bolt on kit with a magnaflow muffler. just not sure what size...
User avatar

By ChicagoMike
- Wed Oct 03, 2007 3:04 am #25090 2.5" should be okay. Thats what I'm running and it flows fine. :thumb:
User avatar

By Greasedmonkey
- Wed Oct 03, 2007 3:20 am #25093 sweet thanks. Ive got the one I bought from a friend that i will rock til i get the kteller. its super quite which I like.
User avatar

By chnzgoofball
- Sat Oct 06, 2007 10:34 pm #25519 isnt 2.5" a little big for all motor? i thought 2.25" was good?? :?
User avatar

By Greasedmonkey
- Wed Oct 10, 2007 10:17 pm #26070 Just picked up my short block. Didnt get the one I had planned on becuase the guy decided to screw me over and tell me the price he said was without pistons and rods instead of without just pistons. Being that I already have pistons, i didnt care about not getting the pistons. Cant make it work with out rods though. So I didnt end up getting the JDM ITR i wanted. I did get a 94 GSR short block with AC compressor and alt. The wierd thing is I always thought GSR pistons said P72 on them, these say P73. Ill get some pics of everything I have when I drop the block off at my dads.
User avatar

By Greasedmonkey
- Wed Oct 10, 2007 11:49 pm #26072 Here are some pics of the block sitting in the back of my hatch.

Image
Image
Image
Image
Image


If you look close, you can see AO P73 on the pistons.
User avatar

By ChicagoMike
- Wed Oct 10, 2007 11:53 pm #26073 You sir, have USDM ITR pistons in that block. :thumb:

If they were JDM ITR pistons, they would say 00 P73, insted of A0 P73.
User avatar

By ChicagoMike
- Thu Oct 11, 2007 3:36 am #26089 Hey, if its gonna be a while before you get that dropped in, put tape across the top of the motor, try to keep any more shit from getting between the piston and the cylinder wall. :thumb:
User avatar

By ChicagoMike
- Thu Oct 11, 2007 4:13 am #26094
teal_dx wrote:but not duct tape... you'll be scraping off the sticky shit it leaves behind (learned the hard way)

do a few strips of the wide masking tape :thumb:


Good lookin out, I forgot to mention that. :lol:
User avatar

By Greasedmonkey
- Thu Oct 11, 2007 12:09 pm #26106 Yea, it will be a while before it goes in. But the pistons and rods will be taken out when I get it on a stand. I have PCT pistons to put in it. Im also going to clean up that block. Its nasty dirty. Gotta get a new oil pump, water pump, tensioner, rear main seal and bearings then I can put the short block back together.
User avatar

By DJ NeX
- Thu Oct 11, 2007 5:43 pm #26150 looks sexy! now put it together!
User avatar

By chnzgoofball
- Thu Oct 11, 2007 10:47 pm #26198 wow thats a lot of carbon build up on the pistons... :shock:
User avatar

By ohDirka
- Thu Oct 11, 2007 11:20 pm #26208
chnzgoofball wrote:wow thats a lot of carbon build up on the pistons... :shock:


x2
 Reply
Return to Naturally Aspirated