- Thu Sep 22, 2011 8:30 am
#273647
I'll have to dig up the picture of mine buried past 150mph haha. I loved that car. And it was the rare Eucalyptus Pearl Green color, five speed, with the tan/black interior.
too bad about the fender
- Thu Sep 22, 2011 5:33 pm
#273721
Yea its the BB6 cluster and out here in the bay area its hard to find a donor car for it, At least when I looked the newest lude I could find was a 96, Its from a 99, I just lucked out on it. Yea I haven't gotten around to the fenders yet I wanna wait till paint to do the body work, That way its all one shot.
- Fri Sep 23, 2011 10:23 am
#273929
Not sure what you mean by plug and play? Its not like an s2k cluster or anything where you need special converters or anything, But I did cut the entire EH cluster wiring harness and re-soldered it to the BB6 cluster's Pig tails. Took me 3 tries to get it right, 5 Different diagrams, and a little lucky guess work. No idea on the hours but i'd say somewhere between 5-10 for wiring, but only because I had to decipher all the other diagrams and match everything up, take it out and put it back in, check if its working, Organize wire clutter, ect... With the correct diagram and diy though I don't think it'd be any harder then any other cluster swap. Fitting the cluster in the dash is a whole another beast...I had to trim the actual bb6 cluster housing to get it to center and it actually sits in there so tight I didn't have to screw it down...Its literally secured in the dashe's housing by pure tension. It also sits closer to you then the stock cluster specially with all the wires behind it, Its a very very tight fit, BUT its rather perfect fit as nothing gets cut off when centered correctly, and when I finally put the acrylic cover it'll fit with no gaps at all. The BB6 cluster is a little bit thicker? then the EG cluster, And the plugs run along the top, So it hits the back of the dashe's cluster area before it sits all the way in. As for the bezel, that was a lot of hand work and that plastic is some nasty stuff I can still taste it in my flem every now and then...I used 3 EG bezels before I figured out how I wanted it to sit, Turns out the EG bezels shape is pretty much a perfect flow with the BB6 cluster's when cut correctly, But you have to sort of squeeze and stretch it to get it to shape it perfectly (bb6 is a tad bit taller in the middle) otherwise something will get slightly cut off. I want another BB6 bezel so I can re-cut the EG bezel perfectly, cuz this ones already glued. I also made mine so that the bezel can be taken off the cluster and they're not one piece in case I do ever get another bezel to work with. I may just separate this one and have another try it after I figure out what to do about the paint.
- Fri Sep 23, 2011 6:19 pm
#274027
Sure I don't see why not. I don't have great memory though and I was in a hurry so somethings may be a little fuzzy or misconstrued. I was gonna do a DIY but seeing as how I mostly just followed the Tegra cluster in EG one I didn't see much reason to, Other then a wiring diagram.
- Fri Sep 23, 2011 8:26 pm
#274040
@ andy Phantom Grey
I love the phantom grey color awesome OEM color cant wait to get it resprayed, But I'm gonna add a little twist in when I respray it, To keep it at least a little uneek
I love the phantom grey color awesome OEM color cant wait to get it resprayed, But I'm gonna add a little twist in when I respray it, To keep it at least a little uneek
- Fri Sep 23, 2011 8:32 pm
#274042
Yea I'm gonna keep it OEM, but have a slight pearl/flake under certain light. I wonder what camellia red pearl would look like on a hatchie.
- Fri Sep 23, 2011 8:45 pm
#274046
I was thinking of doing a DA Audio console since the HOP is so damn hard to find now. I Love fabrication so expect a lot of random parts from other cars 
I thought about the prelude center console as well but I don't like the offset of the ebrake, or how deep the audio console parts sits in the dash The (EK has it too). I want more of a flush look. I had a buddy with a 4dr who fabbed in a EK center console and was thinking of following in his footsteps.
I thought about the prelude center console as well but I don't like the offset of the ebrake, or how deep the audio console parts sits in the dash The (EK has it too). I want more of a flush look. I had a buddy with a 4dr who fabbed in a EK center console and was thinking of following in his footsteps.
Last edited by Wicked on Fri Sep 23, 2011 8:55 pm, edited 3 times in total.